Woodworking

Sandpaper Grit Chart: Grades, P vs US Numbers, Which Grit

By Hods Published

A lower grit number means coarser paper: 40 grit removes material fast and leaves deep scratches, 120 grit smooths bare wood, and grits in the thousands are used to wet-sand paint and clear coat before polishing. The number describes the size of the abrasive particles bonded to the sheet. Two main systems are in use, the US CAMI scale (bare numbers such as 120) and the European FEPA scale (numbers with a “P” prefix such as P120). They agree closely up to 220 and drift apart above it: in Klingspor’s conversion chart, a US 1000 sheet has the same average particle size as P2000.

Quick answer: what each grit range does

Grit rangeCommon nameTypical work
24-60Extra coarse to coarseStock removal, flattening, stripping thick finish
80-100MediumRemoving planer and saw marks, first pass on rough wood
120-150FineSecond pass, smoothing before finer sanding, drywall and flooring
180-240Very fineFinal sanding of bare wood before a finish
320-400Extra fineBetween coats of paint or primer
600-2000+SuperfineWet sanding paint and clear coat, polishing preparation

Names and boundaries vary by maker. Mirka’s belt-sanding guide, for example, groups P24-P80 as coarse sanding and calibration, P100-P320 as medium and wood sanding, and P320-P1200 as intermediate and fine sanding, with P320 listed in both of the last two (Mirka belt sanding guide).

What the grit number means

A grit number comes from screen sizing. Klingspor’s glossary defines grit as the “designation of abrasive grain size, reflecting the number of the smallest openings per linear inch in the screen through which the grain will pass,” and notes it can be either a US “C.A.M.I.” grade or a European “P” grade (Klingspor glossary). A higher number means a finer screen, so smaller grains.

That is why the numbers run backward from intuition. For coarse grits the abrasive particle is large and the number is small; for polishing grades the particle is smaller still and the number runs into the thousands.

Grains are not all one size. Each grade is a distribution around an average. The micrometre (one thousandth of a millimetre) figures in the table below are average particle sizes, and they are the cleanest way to compare grades across systems.

Grit conversion table: P-grade vs US CAMI in micrometres

The table gives the average particle size for the same number in each system, as listed in the “Grit System Conversion Chart” on Klingspor’s grit grading systems page, which compares the FEPA P-grade and CAMI scales in inches and microns (Klingspor grit grading systems). The sizes are that manufacturer’s comparison values, and Klingspor does not say how it derived them. The last column is calculated from Klingspor’s figures.

NumberP-grade (FEPA) average size, µmUS CAMI average size, µmLarger grain, by
36524535CAMI, 2%
40412428CAMI, 4%
50326351CAMI, 8%
60260268CAMI, 3%
80197192P, 3%
100156141P, 11%
120127116P, 9%
1509793P, 4%
1807878same
2206566CAMI, 2%
24058.553.5P, 9%
32046.236.0P, 28%
36040.528.8P, 41%
40035.023.6P, 48%
50030.219.7P, 53%
60025.7516.0P, 61%
80021.812.3P, 77%
100018.39.5P, 93%

Klingspor’s chart also lists P1200 at 15.3 µm, P1500 at 12.3 µm and P2000 at 9.5 µm, and it places P1500 and P2000 in the same rows as CAMI 800 and CAMI 1000. In other words, US 1000 grit is about the same particle size as European P2000.

A metallography supplier that publishes conversions for both scales reaches the same conclusion in words: ANSI/CAMI numbers above 220 use a separate scale from FEPA, FEPA P-grades follow the ISO 6344 standard with micron values given as median particle size, and equivalents above 220 are approximate because the standards measure particle size differently (Pace Technologies converter). Its conversion table also pairs US 800 with P1500 and US 1000 with P2000.

The two sets of figures differ in detail. Pace’s ISO 6344 sizes for P36 to P220 run 2 to 5 percent larger than Klingspor’s (P60 at 269 µm against 260, P80 at 201 against 197), except at P120 and P180, where they match; from P240 to P1200 the two lists agree; and Pace gives P1500 as 12.6 µm and P2000 as 10.3 µm, against Klingspor’s 12.3 and 9.5. Some pairings differ too: Pace matches US 400 with P600, while Klingspor’s 23.6 µm for US 400 falls between P600 and P800. Use the numbers to compare grades, not as specifications.

Where the two systems diverge

Up to 220, Pace’s converter gives each US number the same P number, and in Klingspor’s chart each pair is within 11 percent. Above 220 the numbers stop meaning the same thing. In Klingspor’s chart:

  • A US 400 sheet has particles of about 24 µm; a P400 sheet has about 35 µm.
  • US 600 (16 µm) is finer than P600 (25.75 µm), and US 1000 (9.5 µm) is finer than P1000 (18.3 µm).
  • A sheet marked P1500 and a US sheet marked 800 share a row at 12.3 µm.

Practical consequence: when an instruction names a fine grit such as 1000 or 2000, check which scale the paper uses. In Klingspor’s chart a US 1000 sheet (9.5 µm) matches P2000, while P1000 (18.3 µm) is nearly twice as coarse.

60 grit vs 80 grit, and 1000 vs 2000

In Klingspor’s chart, P60 particles average 260 µm and P80 particles 197 µm, so 80 grit is about three-quarters the particle width of 60 grit: a clear step, but both are coarse and both leave scratches that a finer grit has to remove. Festool starts planed wood at P80 to even out planing strokes and uses Granat P40-P80 to sand stair surfaces smooth and flat, so 60 suits heavier removal and 80 suits evening out marks.

At 1000 versus 2000, the answer depends on the system. P1000 averages 18.3 µm and P2000 9.5 µm in Klingspor’s chart (10.3 µm in Pace’s ISO 6344 list), so P2000 grains are roughly half the size. On the US scale, Klingspor puts 1000 at 9.5 µm, the same as P2000, so “1000 vs 2000” can describe two sheets with the same grain when one is US-graded and the other P-graded.

Which grit for which job

The table below combines the manufacturer guidance cited in the sections that follow.

JobGrit rangeBasis
Stripping, rough shaping, flattening woodP40-P80Festool Granat P40-P80 for flat, smooth first sanding; Mirka P24-P80 as coarse
Removing planer or knife marksP80, then P120Festool planing guide
Final sanding of bare wood before a clear finishP150-P180, or higher if the coating, wood or finish maker calls for itFestool; Mirka
Oiled floors and similarP120-P150Mirka oiling guide
Oiled furniture and finer surfacesP150-P180Mirka oiling guide
Drywall joint compound, by hand100-120, then 150-220National Gypsum
Walls, ceilings and filler, power sandedP80/P120/P180; P120, P180 then P240 for paintMirka wall guide
Between coats of primer or paintP320-P400Mirka wall guide
Wet sanding automotive clear coat1500 to sand the clear coat, then 3000 damp sanding before polishingMirka post-paint process
MetalChoose the mineral first, then work coarse to fineKlingspor material recommendations

Bare wood: 80, 120, then 150 to 180

Festool’s guide to sanding after planing starts at P80 “to even out planing strokes,” then switches to P120 once the planing marks are gone, and finishes at “P150, P180 or even higher” depending on the coating and wood, with the instruction to “always follow the recommendations of the varnish or oil manufacturer” (Festool planing guide). On a staircase, the same maker’s guide uses Granat P40-P80 for the coarse stage and Rubin P100-P150 for fine sanding (Festool stair guide).

For most furniture or shelf projects, that pattern reduces to 80, 120, then 180 or 220, which puts 120 grit at the stage after the coarse marks are gone and before the last fine pass.

Finer is not always better on bare wood. Mirka recommends P120-150 for flooring and P150-180 for finer surfaces such as furniture when oiling, and warns that sanding too fine “closes fibres in the wood which results in the oil or wax not penetrating the surface” (Mirka wood oiling guide). Festool also suggests watering oak and similar woods before the final sanding: dampening the surface makes “the wood fibres stand up,” and once dry they can be evened out with a final fine sanding.

For glue-ups, wood glue types compared covers the adhesive choice, and the wood selection guide covers choosing species and making a labelled finishing sample that records the sanding and coating sequence.

Drywall and painted walls

National Gypsum advises manual drywall sanding at “100-120 grit,” then “150-220 grit for finish work,” and says to “avoid anything under 100 grit” because it is “too aggressive and can damage drywall”; for power sanding it advises finer grits to prevent over-sanding (National Gypsum drywall sanding tips). It also says dry sanding is faster but “produces significantly more dust” than wet sanding with a damp sponge.

Mirka’s wall guide suggests P80, P120 and P180 as the working set for walls and ceilings, P120 to flatten filler, P180 to refine it and P240 for a paint-ready surface, and P320-P400 to de-nib between primer and topcoats (Mirka wall and ceiling guide).

Metal

Klingspor’s material recommendations name the abrasive mineral for each metal rather than a grit: aluminium oxide and alumina zirconia are generally used on ferrous metals; on stainless steel, alumina zirconia or aluminium oxide, with silicon carbide “sometimes used for final finishing because a more consistent scratch pattern is achieved”; and on non-ferrous metals, open-coat alumina zirconia for rough grinding, then aluminium oxide and silicon carbide for intermediate and finish sanding (Klingspor recommendations). The page gives no grit numbers.

Wet sanding automotive clear coat

Automotive finishing moves into the fine end of the scale, where US and P numbers diverge most. Mirka’s post-paint process for removing orange peel, scratches and other imperfections starts by sanding the clear coat with its Galaxy abrasive in 1500 grit, moves to damp sanding with Abralon in 3000 grit, with water sprayed on both the abrasive and the surface, and finishes with two polishing stages, Polarshine 20 and then the finer Polarshine 5 (Mirka automotive post-paint polishing). Follow the paint maker’s data sheet for how much clear coat can be removed.

How far to jump between grits

A Fisheries Supply listing for 3M Pro Grade Precision sanding sheets gives the instruction “Do not skip more than 1 grit between each sanding step,” and advises sanding with the grain of wood, “working through a sequence of grits from coarse to very fine” (Fisheries Supply: 3M Pro Grade Precision sheets). Sherwin-Williams’ listing for 3M’s Pro Grade Precision Ultra Flexible sheets gives the same rule, “skipping no more than 1 grit between each sanding step” (Sherwin-Williams: 3M Ultra Flexible sheets). On a grit series of 60, 80, 100, 120, 150, 180, 220, 240, 320 and 400, skipping one grit means going from 80 to 120 or from 120 to 180, not from 80 to 180.

The reasoning is in Festool’s planing guide: the marks left by coarse sanding have to be removed during fine sanding so that they are “no longer visible after the surface treatment.” Mirka’s belt sanding guide lists “steps too big in grit sequence” as a cause of an uneven surface and, as a way to keep sanding costs down, advises avoiding “sanding with finer grits than necessary” (Mirka belt sanding guide).

Using Klingspor’s P-grade sizes, the common 80, 120, 180 sequence runs from about 197 to 127 to 78 µm, each step cutting the particle width by roughly 35-40 percent. A jump from 80 straight to 220 (65 µm) would cut it by two thirds in one step and skip four grits on the series above, well past the one-grit limit.

Abrasive minerals and backings

The grit number says how big the grain is; the mineral says what it is made of. Klingspor’s glossary defines the main ones:

MineralWhat it isKlingspor’s notes on use
Aluminium oxideMade by fusing bauxite; very strong and tough; normally brown or reddish brown”the most commonly used abrasive for sanding and grinding of wood and metal”
Silicon carbideMade from coke and silica sand; very sharp and hard; normally blackSoftwoods, painted or finished surfaces, rubber, plastic and non-ferrous metals; cuts very well under light pressure
GarnetNatural red grain made by crushing garnet; fractures quickly, which keeps it sharpWood end grain and final-finish sanding of wood; “still used occasionally” in woodworking
Alumina zirconiaAlloy of aluminium oxide and zirconium oxide; self-sharpening; belts normally blueHeavy-duty stock removal on metal and wood
Ceramic aluminium oxideBauxite and other ingredients, chemically bondedNo specific use given; described as “exceptionally hard, strong, and sharp”

Source: Klingspor glossary.

Coating density matters too. Klingspor defines open coat as abrasive grain covering about 50 percent to 70 percent of the surface, which “helps to retard loading of sticky or gummy materials such as softwoods or paint,” and names paper, cloth and vulcanized fibre as the major backings. Festool lists its wood abrasive Rubin 2 on “robust paper backing,” its coarse Saphir on cloth, a foam-backed Granat Soft for walls and ceilings, and an open-mesh Granat Net for dusty jobs such as filler (Festool abrasive overview).

Dust and health

Sanding is among the dustiest woodworking jobs. OSHA’s woodworking eTool says sanders, shapers and routers “generally produce the greatest amount of dust” and names local exhaust ventilation as “the primary method of controlling wood dust” (OSHA woodworking eTool). It lists the effects of wood dust as including dermatitis, asthma, hypersensitivity pneumonitis and chronic bronchitis, and says certain hardwoods, among them oak, mahogany, beech, walnut, birch, elm and ash, have been reported to cause nasal cancer in woodworkers.

Two US federal bodies publish different exposure figures for wood dust:

LimitSet byFigureStatus
Permissible exposure limit (PEL)OSHA15 mg/m3 total dust and 5 mg/m3 respirable fraction, 8-hour time-weighted averageRegulatory limit; OSHA regulates wood dust under its limit for particulates not otherwise regulated (nuisance dust)
Recommended exposure limit (REL)NIOSH1 mg/m3, time-weighted averageRecommendation; NIOSH lists wood dust as a potential occupational carcinogen

Both sets of figures appear in the eTool above. OSHA’s wood dust standards page confirms that wood dust falls under the particulates-not-otherwise-regulated limit, and the NIOSH Pocket Guide entry for wood dust gives the 1 mg/m3 recommendation, one fifteenth of OSHA’s total-dust limit.

OSHA’s wood dust hazard page adds that the National Toxicology Program lists wood dust as “known to be a human carcinogen” and IARC classifies it as carcinogenic to humans (Group 1), and notes that OSHA’s January 1989 air contaminants rule, which covered wood dust, was remanded by a federal appeals court and its limits are not in force (OSHA wood dust hazards). Mirka’s own advice for wall sanding is a mask and protective gear plus extraction through the abrasive (“the moment it’s created”), and National Gypsum recommends a dust mask or respirator, ventilation and tools with dust collection attachments.

At home, the practical steps are to connect a sander to a vacuum or extractor (Festool’s stair guide attaches a 27 mm extractor hose to the sander for both the coarse and fine stages), to wear a respirator suited to fine dust, and to leave room in the shop for dust collection; the garage workshop layout guide covers space for the collector, its hoses and emptying. The first workbench build covers the plan, cut list and hardware for a bench to do this work on.

Sources