Woodworking

Lumber Nominal vs Actual Sizes: 2x4, 4x4, 1x6 and Plywood

By Hods Published

A 2x4 is 1-1/2 inches by 3-1/2 inches (38.1 by 88.9 mm) when it is dry. The American Softwood Lumber Standard says so directly: “a dry 2 by 4 is surfaced to 38.1 mm by 88.9 mm (1 1/2 by 3 1/2 inches).” A 1x6 is 3/4 by 5-1/2 inches, a 2x10 is 1-1/2 by 9-1/4, and a 4x4 is 3-1/2 by 3-1/2. The “2 by 4” is a label for a size category. It was never a promise about what the board measures.

The numbers below come from the standard itself (NIST Voluntary Product Standard PS 20-25, January 2025), the National Hardwood Lumber Association (NHLA) rulebook for hardwood, the plywood and structural-panel standards PS 1 and PS 2, and the USDA Forest Products Laboratory Wood Handbook.

Quick answers: actual size of common lumber

Nominal sizeActual (dry), inchesActual (dry), mmActual (green), inches
1x23/4 x 1-1/219.1 x 38.125/32 x 1-9/16
1x43/4 x 3-1/219.1 x 88.925/32 x 3-9/16
1x63/4 x 5-1/219.1 x 139.725/32 x 5-5/8
1x83/4 x 7-1/419.1 x 184.225/32 x 7-1/2
1x103/4 x 9-1/419.1 x 235.025/32 x 9-1/2
1x123/4 x 11-1/419.1 x 285.825/32 x 11-1/2
2x41-1/2 x 3-1/238.1 x 88.91-9/16 x 3-9/16
2x61-1/2 x 5-1/238.1 x 139.71-9/16 x 5-5/8
2x81-1/2 x 7-1/438.1 x 184.21-9/16 x 7-1/2
2x101-1/2 x 9-1/438.1 x 235.01-9/16 x 9-1/2
2x121-1/2 x 11-1/438.1 x 285.81-9/16 x 11-1/2
4x43-1/2 x 3-1/288.9 x 88.93-9/16 x 3-9/16
4x63-1/2 x 5-1/288.9 x 139.73-9/16 x 5-5/8
6x65-1/2 x 5-1/2139.7 x 139.75-1/2 x 5-1/2
8x87-1/4 x 7-1/4184.2 x 184.27-1/2 x 7-1/2

These are the minimum dressed sizes in PS 20-25, Table 3. The standard states the inch values as the units of record and gives the metric values “for information and comparison only.” Lengths are different: the Wood Handbook notes that “lumber length is recorded in actual dimensions,” so an 8-foot board is 8 feet or slightly longer. Unless the purchase contract says otherwise, PS 20 has lumber 2 inches or less in nominal thickness trimmed at both ends to at least the nominal length and no more than 3 inches over it. For nominal 2-inch dimension lumber over 12 inches wide or over 20 feet long, the overlength allowance is 12 inches.

Full dressed-size chart (PS 20)

PS 20 lists thickness and width separately, and “the thicknesses apply to all widths and all widths apply to all thicknesses.” Look up each dimension in its own table and combine them. A 1x6 pairs the 1-inch thickness with the 6-inch width.

Thickness: boards, dimension lumber and timbers

Nominal thicknessDry (19% moisture or less)Dry, mmGreen (over 19%)Green, mm
3/85/167.911/328.7
1/27/1611.115/3211.9
5/89/1614.319/3215.1
3/45/815.911/1617.5
13/419.125/3219.8
1-1/4 (5/4)125.41-1/3226.2
1-1/2 (6/4)1-1/431.81-9/3232.5
21-1/238.11-9/1639.7
2-1/2250.82-1/1652.4
32-1/263.52-9/1665.1
3-1/2376.23-1/1677.8
43-1/288.93-9/1690.5
4-1/24101.64-1/16103.2
5 and 6 (timbers)1/2 less than nominal12.7 less1/2 less than nominal12.7 less
7 to 15 (timbers)3/4 less than nominal19.1 less1/2 less than nominal12.7 less
16 and over (timbers)1 less than nominal25.4 less1/2 less than nominal12.7 less

Width: boards and dimension lumber

Nominal widthDryDry, mmGreenGreen, mm
21-1/238.11-9/1639.7
32-1/263.52-9/1665.1
43-1/288.93-9/1690.5
54-1/2114.34-5/8117.5
65-1/2139.75-5/8142.9
7 (boards)6-1/2165.16-5/8168.3
87-1/4184.27-1/2190.5
9 (boards)8-1/4209.68-1/2215.9
109-1/4235.09-1/2241.3
11 (boards)10-1/4260.410-1/2266.7
1211-1/4285.811-1/2292.1
1413-1/4336.613-1/2342.9
1615-1/4387.415-1/2393.7

Three patterns make the chart easy to carry in your head. Dry widths of 2 to 7 inches lose a half inch. Dry widths of 8 inches and up lose three-quarters of an inch. A 2-inch-thick piece is always 1-1/2 inches thick when dry. Timbers (nominal 5 inches and thicker) follow their own rule, the same for thickness and width: PS 20 notes they are “often manufactured and sold without drying,” their green size is simply 1/2 inch under nominal, and their dry size is 1/2 inch under at 5 and 6 inches, 3/4 inch under from 7 to 15, and 1 inch under at 16 and over. That is why a 6x6 is 5-1/2 inches square and a dry 8x8 is 7-1/4.

Redwood, western red cedar and northern white cedar are exceptions on green width. PS 20 gives them their own table of minimum green widths, which match the general table at nominal 3 and 4 inches and then run 1/16 to 1/8 inch narrower: 5-9/16 inches for a nominal 6 (against 5-5/8 for other species) and 7-3/8 for a nominal 8 (against 7-1/2). The standard also gives these three species a lower shrinkage and expansion allowance: 0.7 percent per four percentage points of moisture change instead of 1 percent.

Why the sizes differ from the label

Width and thickness, in the Wood Handbook’s words, “are traditionally recorded in ‘nominal’ dimensions,” and the actual dimensions “are somewhat less.” Three steps separate the label from the board you buy, and PS 20 accounts for each one.

  1. Sawing allowance. For lumber of nominal 1 inch and thicker, PS 20 sets the minimum rough thickness at 1/8 inch over the minimum dressed thickness (up to 20 percent of a shipment may be as little as 3/32 inch over), and the minimum rough width at 1/8 inch over the dressed width. Rough stock is therefore cut slightly oversize so that surfacing can clean it up.
  2. Drying shrinkage. The standard defines dry lumber under nominal 5 inches thick as lumber dried to a maximum of 19 percent moisture content. Green lumber is dressed larger. The Wood Handbook explains that green lumber surfaced to the standard green size “will shrink to approximately the standard dry size as it dries to about 15% moisture content.” A PS 20 footnote gives the basis: the minimum green sizes rest on shrinkage factors of 2.35 percent in thickness and 2.80 percent in width from the fiber saturation point to 19 percent moisture content.
  3. Surfacing. Planing both faces and edges makes the piece smooth and uniform in size. PS 20 describes surfacing as done “to attain smoothness of surface and uniformity of size.” Rough lumber, by contrast, still shows saw or other primary manufacturing marks on all four long surfaces.

Moisture keeps working after you buy the board. PS 20 says its sizes “pertain to those items as measured at time of manufacture” and that lumber “will change in dimension (shrink or expand) in response to its equilibrium moisture content.” It allows a tolerance of 1 percent shrinkage or expansion for each four percentage points of moisture change. Those are averages; a footnote adds that “the range of shrinkage of individual pieces from experimental observation is from 2% to 7%.” At the average rate, the 3-1/2-inch face of a 2x4 moves about 0.035 inch, roughly 1/32, for every four points of moisture change.

How today’s sizes came about

PS 20’s own history section records the sequence. Early in 1922, Commerce Secretary Herbert Hoover, responding to a request from the lumber industry, offered the Department’s cooperation in simplification, standardization and quality guarantees for lumber buyers. That led to Simplified Practice Recommendation R 16, published in 1924, with later editions in 1925, 1926, 1929, 1939 and 1953. R 16-53 was revised in 1969 and superseded by Voluntary Product Standard PS 20-70. PS 20 lists five significant provisions added in PS 20-70, and the first is separate size standards for dry and green lumber under nominal 5-inch thickness, established “in order to achieve greater uniformity in the dimensions of seasoned and unseasoned lumber at the point of use.” PS 20 describes the later changes, in 1985, 1991, 1992, 1999, 2005, 2010, 2015 and 2020, as non-substantive. The current edition, PS 20-25, took effect in January 2025 with “the same technical requirements” as its predecessor, PS 20-20 Revision 1.

The standard also refuses to treat the labels as measurements: “No inferences shall be drawn that the ‘nominal’ sizes are dressed sizes.”

What 5/4, 6/4 and 8/4 mean

Hardwood is sold by thickness in quarters of an inch of the rough board: 4/4 is 1 inch, 5/4 is 1-1/4 inches, 6/4 is 1-1/2 inches, 8/4 is 2 inches. The NHLA rulebook lists standard rough thicknesses and says “one inch and thicker may also be expressed in quarter inches” as 4/4, 5/4, 6/4, 7/4, 8/4, 10/4, 12/4, 14/4, 16/4 and so on up to 24/4.

If the board is surfaced on both sides (S2S), NHLA’s rule subtracts 3/16 inch from the rough thickness for lumber up to 1-1/2 inches, and 1/4 inch for lumber from 1-3/4 to 4 inches. The Wood Handbook prints the same table (its Table 6-4).

Quarter nameRoughSurfaced two sides (S2S)S2S in mm
none (3/4 in.)3/49/1614
4/4113/1621
5/41-1/41-1/1627
6/41-1/21-5/1633
7/41-3/41-1/238
8/421-3/444
10/42-1/22-1/457
12/432-3/470
16/443-3/495

Two cautions follow from the rulebook. First, thickness of lumber surfaced on one side only (S1S) “shall be subject to special contract,” so no standard number exists for S1S boards. Second, the label names the rough stock the board came from, and the S2S figure above is the NHLA standard value, not a guarantee from any particular seller. Measure the board you are handed.

Softwood uses a similar-looking label with different arithmetic. In PS 20, a board with nominal thickness 1-1/4 (a “5/4” board) is 1 inch thick when dry, and a nominal 1-1/2 (“6/4”) board is 1-1/4 inches dry. The Wood Handbook describes radius-edged softwood decking the same way: “nominal 5/4- or 2-in.-, actual 1- or 1-1/2-in.” thick.

Width works differently from thickness. NHLA’s hardwood grades set minimum widths rather than standard widths, and hardwood is usually manufactured to random widths, so you buy by the board foot rather than by a “1x6” style label.

Plywood and OSB: nominal vs actual thickness

Structural plywood and OSB use a different system. Under PS 2 (wood structural panels, including OSB) and PS 1 (structural plywood), each panel carries a Performance Category. PS 2 defines it as “a panel designation related to the panel thickness range that is linked to the nominal panel thickness designations used in the International Building Code (IBC) and International Residential Code (IRC).” The category is the label, and the actual thickness is allowed to land anywhere in a range around it.

Performance CategorySheathing and unsanded range (PS 1 and PS 2), in.Sanded plywood range (PS 1), in.
3/80.344 to 0.4060.359 to 0.391
15/320.438 to 0.5000.453 to 0.484
1/20.469 to 0.5310.484 to 0.516
19/320.563 to 0.6250.578 to 0.609
5/80.594 to 0.6560.609 to 0.641
23/320.688 to 0.7500.703 to 0.734
3/40.719 to 0.7810.734 to 0.766
1-1/81.069 to 1.1811.091 to 1.159

The tolerance is plus or minus 1/32 inch for categories of 13/16 and under, and plus or minus 5 percent above that, on sheathing and unsanded grades. Sanded plywood is held tighter: plus or minus 1/64 inch up to 3/4 category and plus or minus 3 percent above it. PS 2 recommends labeling a 23/32 panel as “Thickness 0.703 IN.” and a 19/32 panel as 0.578 in.

The practical result: 23/32 and 3/4 are separate categories with different thickness ranges, even though PS 2’s span-rating tables pair them (“23/32 & 3/4” at a 48/24 sheathing rating and a 24-inch single-floor rating). A 23/32 panel may measure 0.688 to 0.750 inch and a 3/4 panel 0.719 to 0.781 inch, so a sheet called “3/4-inch” can be either. The stamp settles it: PS 1 and PS 2 both require each panel to show its Performance Category and its thickness in thousandths of an inch. For plywood, that decimal label dates from PS 1-09, effective May 2010, which created the Performance Category in response to consumer complaints that thickness labeling was out of compliance with NIST Handbooks 130 and 133.

Length and width stay close to the label. PS 2 allows plus or minus 1/16 inch on the manufacturer’s stated length and width. PS 1 allows nothing over and up to 1/16 inch under, or up to 1/8 inch under for panels marked “sized for spacing,” which the maker has sized to allow for industry-recommended installation gaps. A “4x8” sheet can therefore measure a little under 48 by 96 inches.

The categories above cover structural plywood and OSB. Cabinet-grade and imported plywood may follow other standards, so check the actual sheet with calipers before cutting a dado.

Compute board feet (with a worked example)

A board foot is 144 cubic inches, a piece 12 inches by 12 inches by 1 inch. PS 20 defines board measure as the nominal thickness in inches times the nominal width in feet times the length in feet. In practice:

Board feet = thickness (in.) x width (in.) x length (ft) / 12

Use the nominal figures for softwood, and the rough (quarter) thickness for hardwood. NHLA’s rule goes further: “in surfaced lumber, board footage is measured before surfacing,” and thicknesses under 1 inch are counted as 1 inch. An NHLA tally also rounds each board’s surface measure (its face area in square feet) to the nearest whole foot before multiplying by thickness.

Examples:

  • A 2x4x8: 2 x 4 x 8 / 12 = 5.33 board feet on the nominal count. The actual piece holds 1.5 x 3.5 x 96 / 144 = 3.5 board feet of wood, about two-thirds of the nominal tally.
  • An 8-foot 4/4 hardwood board, 8 inches wide: 1 x 8 x 8 / 12 = 5.33 board feet. If it arrives S2S at 13/16, NHLA measure still counts the full 1 inch. On an NHLA tally its surface measure of 5.33 square feet rounds to 5, so it tallies as 5 board feet.
  • A 6/4 board, 7 inches wide, 10 feet long: 1.5 x 7 x 10 / 12 = 8.75 board feet. On an NHLA tally the surface measure of 5.83 square feet rounds to 6, giving 6 x 1.5 = 9 board feet.

Worked purchase: a bench top and a shelf

The job below is built from the numbers above. For a different starter design, how to build your first workbench lays out a 48-by-24-inch bench from six 8-foot 2x4s and 5/8-inch plywood panels, and the project material calculator shows how to turn a cut list into stock lengths and board feet.

The job: a 60-inch-long bench top, 24 inches deep, built from 2x4s laid flat and edge-glued, with a 3/4-inch hardwood shelf below it.

Step 1, the top. Each 2x4 contributes 3-1/2 inches of width, not 4. Seven boards give 7 x 3.5 = 24.5 inches. Six give 21 inches, 3 inches short. Counting nominal widths would suggest six boards (6 x 4 = 24) and leave the top 3 inches shallow; the same count would have promised 28 inches from seven. Buy seven 8-foot 2x4s (each cut to 60 inches leaves about 36 inches for stretchers), and plan to trim the 24.5-inch panel to 24 after gluing. That half-inch margin is thin: PS 20 notes that lumber of nominal 4 inches or less in thickness “is frequently shipped with eased edges,” and jointing those rounded corners square for tight glue lines narrows every board, so lay the jointed boards side by side and measure before gluing. The top is 1-1/2 inches thick.

Step 2, the shelf. Three pieces, each 7 inches wide, 48 inches long, 3/4 inch thick. Surface area: 3 x 7 x 48 = 1,008 square inches, or 7 square feet. Using 4/4 stock that is 7 board feet of finished area. Add 25 percent for defects and trim: about 8.75 board feet. Two 4/4 boards, 8 inches wide and 8 feet long, give 2 x 5.33 = 10.67 board feet (10 on an NHLA tally), comfortably over. Length is the tighter limit: three 48-inch pieces mean one board must yield two, and a board of exactly 96 inches cannot once the saw kerf comes out, so pick boards that run a few inches over 8 feet. If they arrive S2S at 13/16, planing to 3/4 removes only 1/16, so the shelf thickness is fine.

Step 3, the legs. Four 4x4 posts are 3-1/2 inches square. Design the leg-to-top joint on 3-1/2, then check the stock before marking.

What the arithmetic shows: the seven-board top came out 3-1/2 inches narrower than the nominal count (24.5 against 28), the hardwood bought as “4/4” lost 3/16 inch to surfacing, and the legs lost 1/2 inch each way. All three are the standard sizes, and a drawing that uses them from the start fits the first time.

Buying tips that follow from the standards

  • Plan with actual sizes and write them on the cut list. PS 20 says invoices for standard-size dressed lumber “should show the number of pieces of each nominal size and length as well as the actual thickness and width.” Ask for that on the order.
  • Check the grade stamp for dry or green. PS 20 requires grade marks to show “whether the lumber was dry or green when manufactured,” and for lumber under nominal 5 inches thick it standardizes the marks: S-DRY (surfaced dry), KD (kiln dried to a maximum of 19 percent moisture at surfacing) or S-GRN (surfaced green). A green-stamped board is dressed larger and will shrink toward the dry size as it dries.
  • Treat any 1/32 to 1/16 variation as normal. Moisture alone shifts dimensions. For joinery, measure each board with a rule or calipers and mark joints from the actual piece. The tape measure tips page covers the sliding hook and reading fractions.
  • For furniture stock, specify rough or S2S and a finished thickness. If the project needs 3/4-inch finished boards, 4/4 rough yields them after planing, and 4/4 S2S at 13/16 leaves a small margin. For 1-1/2-inch legs and tops, buy 8/4: S2S at 1-3/4 leaves a quarter inch to plane.
  • Match plywood to the dado. PS 1 holds a 23/32 sanded panel to 0.703 to 0.734 inch, so a dado cut to exactly 3/4 inch (0.750) leaves 0.016 to 0.047 inch of slack across the shelf’s thickness. Size the dado to a test piece from the actual sheet, or use an undersized plywood bit.
  • Do not mix nominal and actual in one stack-up. Measure the finished width of anything you build from 1x6s: three of them cover 16-1/2 inches, not 18.
  • Compare species and grade after size. Standard sizes apply across softwood species (redwood, western red cedar and northern white cedar differ only in green width), and the wood selection guide matches common species to projects and covers inspecting each board.

Sources